C1902 Introduction
产品简介
The C1902 is a development board specifically designed for Jetson Orin Nano & NX modules. Built on a standard board design, it fully supports the official developer kit's features, including full-speed USB3.0 and Type-C ports.
正面
背面
产品特点
-
C1902 was developed based on the original manufacturer's solution, with all interface functions matching the original manufacturer's and supporting direct firmware flashing via Developer Kit
-
Compatible with NVIDIA® Jetson Orin Nano (4GB/8GB) and Orin NX (8GB/16GB) modules.
-
Premium 8-layer gold-plated PCB with full MLCC capacitors and gold-plated connectors
-
Supports M.2 NVMe SSD and M.2 Wi-Fi module
版本迭代记录
|
Version |
Date |
Description |
|
V1.0 |
2024 Q3 |
The first version of C1902 |
|
V1.1 |
2025 Q1 |
1. Fixed a GPIO issue that previously caused pins 12/35/38/40 to be unavailable under the original device tree. 2. Enhanced support for the SUPER mode across the entire ORIN NANO/NX series |
|
V1.1.1 |
2025 Q2 |
3. Modify the DC power input socket specifications from DC5521 to DC5525 |
产品规格
|
Supply Voltage |
12V (compatible with 9-19V) |
|
Operating Temperature |
0℃~45℃ |
|
Supported Module |
Orin Nano 4G/8G Orin NX 8G/16G |
|
Power Connector |
DC5525 |
|
Ethernet |
1x Gigabit Ethernet Socket (RJ45) |
|
Wireless Network Adapter |
1x M.2 Key E |
|
External Storage |
2x M.2 Key M (NVME SSD) |
|
DisplayPort |
1x DP V1.2 |
|
USB |
4x USB3.2 (10Gbps) |
|
USB C |
1x Type C (USB3.0) |
|
Camera |
2x CSI-22P |
|
Other |
Consistent with original specs |
|
RTC |
support |
|
POE |
not supported |
-
The carrier board requires a 12V(compatible with 9-19V) DC power supply. To ensure normal system operation, a power adapter with sufficient current output must be used. Additionally, under high load conditions with an input voltage exceeding 15V, adequate heat dissipation must be provided to prevent overheating.
-
This product includes reverse-polarity protection. Nevertheless, do not connect the power supply in reverse.
- The over-current protection (OCP) threshold for all USB ports is 2.5A. Exceeding this limit will trigger an automatic shutdown of the power output.
- In contrast to the original M.2 2230 interface, the backplane's network interface now features a symmetrical layout.
-
Do not hot-swap the module. Always power off the board before inserting or removing the module. Failure to do so may damage the module and the carrier board. Damage caused by improper operation is not covered under warranty.
功能对比：
|
|
Original |
C1901 V1.3 |
C1902 V1.1 |
|
Supply Voltage |
19V |
12V (compatible with 9-19V) |
12V (compatible with 9-19V) |
|
Power Connector |
DC5525 |
DC5521 (compatible with DC5525) |
DC5525 |
|
Ethernet |
1x Gigabit Ethernet Socket (RJ45) |
1x Gigabit Ethernet Socket (RJ45) |
1x Gigabit Ethernet Socket (RJ45) |
|
Wireless Network Adapter |
1x M.2 Key E |
1x M.2 Key E |
1x M.2 Key E |
|
External Storage |
2x M.2 Key M |
2x M.2 Key M |
2x M.2 Key M |
|
Display |
1x DP V1.2 |
1x HDMI (1080P) |
1x DP V1.2 |
|
USB |
4x USB3.0 |
3x USB3.0+1 xUSB2.0 (requires device tree modification) |
4x USB3.0 |
|
USB C |
1x Type C (USB3.0) |
1x Type C (USB2.0) |
1x Type C (USB3.0) |
|
Camera |
2x CSI-22P |
2x CSI-22P |
2x CSI-22P |
|
RTC |
Not Supported |
Supported |
Supported |
|
Other |
- |
Match the original |
Match the original |
|
POE |
Supported (Not Populated) |
Not Supported |
Not Supported |
|
SUPER Mode |
Only ORIN NANO series is supported |
Only ORIN NANO series is supported |
Supports the ORIN Nano/NX series |
接口布局
|
1 |
Power Jack |
9 |
Camera (#0) Connector (22p, 0.5 mm) |
|
2 |
DP Connector |
10 |
Power Button |
|
3 |
USB 3.0 Type A(x2 Stacked) |
11 |
Button Header (1x12, 2.54 mm) |
|
4 |
USB 3.0 Type A(x2 Stacked) |
12 |
CAN Bus Header (1x4, 2.54 mm) |
|
5 |
RJ45 Ethernet Socket |
13 |
Fan Header |
|
6 |
USB Type C |
14 |
40-pin Expansion Header(2x20, 2.54 mm) |
|
7 |
Jetson Orin Module Connector |
15 |
Power LED |
|
8 |
Camera (#1) Connector (22p, 0.5 mm) |
|
|
|
16 |
RTC Socket |
18 |
M.2 Key M Socket (4-lane) |
|
17 |
M.2 Key E Socket (75-pin) |
19 |
M.2 Key M Socket (2-lane) |
部分功能说明
- 启动按钮 (10)：相比于原厂载板，C1902多设置了一个启动按钮，该按钮具有以下功能：
- 系统启动时：按动一次进入关机界面，长按 10 秒强制关机。
- 系统关闭时：按动一次进行开机。
- 40PIN排针 (14)：40Pin GPIO排针中的 5V 输出具有倒灌保护，该 5V 输出最大电流为 0.8A，过流会关断输出，参考定义如下（实际以核心卡为准）。
- 12Pin调试接口 (11) 定义如下：
- 固态硬盘必须使用单面版本，使用双面贴片版本固态硬盘，有可能发生干涉，引起短路。
- 电池接口 (4)：相比于原厂载板，C1901 多设置了一个 RTC 电池连接器，该连接器型号为 MX1.25-2P，电池电压为 3V。使用电池时，请确认好极性，禁止接反电池。
接入电池后，需要进行配置才能启用 RTC 时钟，详情请参考 RTC 说明
产品尺寸 (mm)
| 螺钉位置 | 推荐的规格 | 备注 |
|---|---|---|
| 载板固定孔 | M2.5 螺钉或铜柱 | 螺钉或铜柱直径不得大于 6mm |
| 核心卡、硬盘 | M2.5 x 4 薄头螺钉 | 推荐使用薄头螺钉，以避免干涉 |
| 网卡 | M2.5 x 4 薄头螺钉 | 推荐使用薄头螺钉，以避免干涉 |